Driving positiomemory system
Your preferred driving position (the position of the driver’s seat, steer- ing wheel and outside rear view mirrors) can be entered into the com- puter’s memory and recalled with the touch of a button. It is also possible to set this function to activate automatically when the doors are unlocked.
Three different driving positions can be entered into memory.
- Entering a position to memory
Turn the “ENGINE START STOP”
switch to IGNITION
ON mode.
Adjust the driver’s seat,
steering wheel, and outside rear
view mirrors to the desired positions.
While pressing the “SET” button, or within 3 seconds after the “SET” button is pressed, press and hold but- ton “1”, “2” or “3” until the signal beeps.
If the selected button has already been preset, the pre- viously recorded position will be overwritten.
- Recalling the memorized position
Check that the shift lever is set in “P”.
Turn the “ENGINE START STOP”
switch to IGNITION
ON mode.
Press button “1”, “2” or “3” to recall the desired position.
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before per- forming the following: ►Using the wireless remote control
Turn the “ENGINE START STOP”
switch to OFF after
closing the driver’s door.
While pressing the desired but-
ton (“1”, “2” or “3”), press
on the wireless remote
control until the signal beeps.
The driving position is recalled when the driver’s door is unlocked using the entry func- tion or wireless remote control and the driver’s door is opened.
To prevent unintended triggering of the alarm, open and close a door
once after a driving position has been recorded. (If a door is not opened
within 60 seconds after is pressed,
the doors will be locked again
and the alarm will automatically be set.)
In case that the alarm is triggered, immediately stop the alarm.
►Using the door lock switch
Carry only the key (including the card key) to which you want to link the driving position. If 2 or more keys are in the vehicle, the driving position cannot be linked properly.
Turn the “ENGINE START STOP”
switch to OFF after
closing the driver’s door.
While pressing the desired but- ton (“1”, “2” or “3”), press the lock or unlock side on the door lock switch (either the driver or passenger side) until the signal beeps.
The driving position is recalled when the driver’s door is unlocked using the enter func- tion or wireless remote control and the driver’s door is opened.
- Canceling the linked door unlock operation
Turn the “ENGINE START STOP”
switch to OFF after closing the
driver’s door.
Using the wireless remote
control: While pressing “SET” button,
press
button on the wireless remote
control until the signal
beeps.
Using the door lock switch: While pressing “SET” button, press the lock or unlock side on the door lock switch until the signal beeps.
- Retained accessory power
l Each memorized position (except for the steering wheel position) can be
activated within 3 minutes after the driver’s door is opened, even if the
“ENGINE START STOP” switch is turned off.
l Each memorized position (except for the steering wheel position) can be
activated within 60 seconds after the driver’s door is closed, even if the
“ENGINE START STOP” switch is turned off.
- To cancel seat position recall
Perform any one of the following operations.
l Press the “SET” button
l Press button “1”, “2” or “3”.
l Adjust the seat using the switches (only cancels seat position recall)
l Adjust the steering wheel using the tilt and telescopic steering control
switch (only cancels steering wheel position recall)
- If the battery is disconnected
The memorized positions must be reset because the computer’s memory is
erased when the battery is disconnected.
CAUTION
- Seat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas-
senger or squeeze your body against the steering wheel.
See also:
Changing the passkey
Select “Set Passkey” using a voice
command or the “TUNE/SEL” knob.
Pattern A
Press the talk switch, say a 4 to
8-digit number, and select “Con- firm” using a voice command or the ...
Hands-free System (For Cellular Phone)
■Bluetooth® phone pairing
Compatible Bluetooth®-equipped phones can be connected to the vehicle,
enabling
hands-free operation. Please refer to the cellular phone manufacturer’s user
g ...
Locking the driver’s door from the outside without a key
Move the inside lock button to the
lock position.
Close the door.
The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or
IGNITION ON mode, or the electronic key is ...